MAX232ECWE Datasheet Download

Part No.:
MAX232ECWE
Download:
Download Datasheet
Description:
[【15kV ESD-Protected, +5V RS-232 Transceivers]
File Size:
1160 K
Page:
25 Pages
Logo:
Manufacturer:
MAXIM [ MAXIM INTEGRATED PRODUCTS ]
PCB Prototype
 MAX232ECWE Datasheet Page:5MAX232ECWE Datasheet Page:6MAX232ECWE Datasheet Page:7MAX232ECWE Datasheet Page:8MAX232ECWE Datasheet Page:10MAX232ECWE Datasheet Page:11MAX232ECWE Datasheet Page:12MAX232ECWE Datasheet Page:13 
±15kV ESD-Protected, +5V RS-232 Transceivers
MAX202E–MAX213E, MAX232E/MAX241E
+5V
0.1µF
*
C1+
0.1µF
*
C1-
V
CC
V+
0.1µF
*
0.1µF
*
+5V
0.1µF
*
C1+
0.1µF
*
C1-
V
CC
V+
0.1µF
*
0.1µF
*
MAX2_ _E
0.1µF
*
C2+ V
CC
C2-
400kΩ
T_
T_IN
R_
R_OUT
0V (+5V)
0V (+5V)
EN (EN)
SHDN (SHDN)
V-
0.1µF
*
C2+ V
CC
C2-
MAX2_ _E
V-
400kΩ
T_OUT
2500pF
R_OUT
0V (+5V)
0V (+5V)
EN (EN)
SHDN (SHDN)
MAXIMUM SLEW-RATE TEST CIRCUIT
( ) ARE FOR MAX213E
* 1µF FOR MAX232E/MAX241E
T_
T_IN
3kΩ
R_
T_OUT
50pF
R_IN
5kΩ
R_IN
5kΩ
7kΩ
MINIMUM SLEW-RATE TEST CIRCUIT
TRANSMITTER INPUT PULL-UP RESISTORS, ENABLE, AND SHUTDOWN ARE NOT PROVIDED ON THE MAX202E, MAX203E, AND MAX232E.
ENABLE AND SHUTDOWN ARE NOT PROVIDED ON THE MAX207E AND MAX208E.
Figure 3. Transition Slew-Rate Circuit
_______________Detailed Description
The MAX202E–MAX213E, MAX232E/MAX241E consist of
three sections: charge-pump voltage converters,
drivers (transmitters), and receivers. These E versions
provide extra protection against ESD. They survive
±15kV discharges to the RS-232 inputs and outputs,
tested using the Human Body Model. When tested
according to IEC1000-4-2, they survive ±8kV contact-
discharges and ±15kV air-gap discharges. The rugged
E versions are intended for use in harsh environments
or applications where the RS-232 connection is
frequently changed (such as notebook computers). The
standard (non-“E”) MAX202, MAX203, MAX205–
MAX208, MAX211, MAX213, MAX232, and MAX241 are
recommended for applications where cost is critical.
into -10V, storing the -10V on the V- output filter
capacitor, C4.
In shutdown mode, V+ is internally connected to V
CC
by
a 1kΩ pull-down resistor, and V- is internally connected
to ground by a 1kΩ pull up resistor.
RS-232 Drivers
With V
CC
= 5V, the typical driver output voltage swing
is ±8V when loaded with a nominal 5kΩ RS-232
receiver. The output swing is guaranteed to meet
EIA/TIA-232E and V.28 specifications that call for ±5V
minimum output levels under worst-case conditions.
These include a 3kΩ load, minimum V
CC
, and
maximum operating temperature. The open-circuit
output voltage swings from (V+ - 0.6V) to V-.
Input thresholds are CMOS/TTL compatible. The
unused drivers’ inputs on the MAX205E–MAX208E,
MAX211E, MAX213E, and MAX241E can be left
unconnected because 400kΩ pull up resistors to V
CC
are included on-chip. Since all drivers invert, the pull up
resistors force the unused drivers’ outputs low. The
MAX202E, MAX203E, and MAX232E do not have pull
up resistors on the transmitter inputs.
9
+5V to ±10V Dual Charge-Pump
Voltage Converter
The +5V to ±10V conversion is performed by dual
charge-pump voltage converters (Figure 4). The first
charge-pump converter uses capacitor C1 to double
the +5V into +10V, storing the +10V on the output filter
capacitor, C3. The second uses C2 to invert the +10V
_______________________________________________________________________________________